ROTOCONE VACUUM DYRER

ROTOCONE VACUUM DYRER
SR. NO.	PARAMETERS	UNITS	USER REQUIREMENT
A	FEED
	Type		Rotocone Vacuum Dryer(cGMP Model)
	Material		Wet Solid material containing solvent,water  of Approx 15%
	Batch size	kg	Varying, Range 100-150 kg wet cake
	PH		5 -11
	Temperature	deg. C	Ambient to 100
	Feed Solvent content	Wt %	10-15%
	Desired Final Solvent & Moisture Content	Wt %	≤ 0.5
	Particle Size	mm	20 to 30micron
	Cake Bulk Density	kg/m3	480
	Corrosion		Yes
	Abrasion		Yes
B	DISCHARGE
	Cake discharge (Solids)		Manual Unloading
C	HEATING REQUIREMENT
	Heating Medium		Hot Water
	Cooling Medium		Cooling water/Chilled Brine
	Limpet / Jacket Material		SS 304
	Limpet / Jacket Design Pressure	bar g	FV to 6
	Limpet / Jacket Design temperature	deg. C	200
D	PROCESS UTILITIES
	Hot Water (Temp. / pressure)	deg. C / bar g	80/4
	Cooling Water(Temp. / pressure)	deg. C / bar g	32/4
	Chilled Brine (Temp. /pressure)	deg. C / bar g	(-20)/4
	Nitrogen  (Temp. / pressure)	deg. C / bar g	Amb/5.5
	Vacuum	bar g	(-) 0.998
E	Cone Design
	Type of Dryer		Rotary Cone Vacuum Dryer
	Design code		ASME SECVIII DIV 1
	Angle		Horizondal axis of rotation
	Cone Volume / Working Volume	liters	100
	Solid holding  Capacity	kgs	50-60ltr.
	Speed	rpm	6-10
	Cone Design Pressure	bar g	FV to 6
	Cone Design Temp.	deg. C	(-30) to 200
	Test Pressure	bar g	VTS
	Operating Pressure	bar g	VTS
	Shell Size	MM	VTS
	Top & Bottom Cone	MM	VTS
	MOC  - SHELL & CONE		SS316
F	Cyclone separator
	MOC		SS316
	Type		VERTICAL
	Filter Bag		Required
	Pulsating System		with FLP Timer
	Capacity	liters	VTS
G	Receiver
	Capacity	liters	VTS
	MOC- Contact / Non Contact Parts		SS316 / SS304
H	Condenser
	Capacity	M2	*
	MOC- Contact / Non Contact Parts		SS316 / SS304
I	MATERIAL OF CONSTRUCTION
	Limpet  / Jacket		SS 304
	Strainer		SS-316
	Supports		SS 304
	Gaskets		FDA Approved food grade quality
	O-ring seals		FDA Approved food grade quality
	Shaft		**
	Shaft Seals		**
	Gear Box		**
	Gear Box Housing		Die Cast Aluminium, Drive Enclosure :- SS304 splash-proof & removable
	Motor Housing
	Surface Finish		-
	Internal Surface Finish		0.5µm Ra (Electropolished)
	External Surface Finish		180 Grit Matt Finish
J	BUYER'S CONNECTIONS
	Clean In-Place Inlet		Not Required
	Hot Water Inlet		Flanged 40mm dia(**)
	Hot Water outlet		Flanged 40mm dia(**)
	Cake charging/unloading		**
	Vacuum		Flanged 50mm dia(**)
	Vent/Nitrogen		Flanged 25mm dia(**)
K	ELECTRICAL
	Power supplied		415 V / 3 Ph. / 50 Hz.
	Motor Make		**
	Motor Rating	HP	**
	Flame Proof - Motor		Yes
	Electrical Pannel		Flame Proof
	Switch, Fuse, Contactor, Ind. Lamp, Push Botton, Wiring		Required
O	GMP STANDERED
	M.S. & Rotating Parts		Covered with SS304 Sheet
	Int. & Ext. Polish		220 Grit, 180 Grit
P	Insulation		Hot Insulation with SS304 cladding
Q	Safety
	Safety Gate		SS304  Gate with prximity switch